Dory

Dory

Saturday, February 22, 2014

Catching Up

So it has been a few weeks since I last updated the blog.  I wish I had a completed boat to show off all of the work we have been putting in.  Well I don't, because we haven't.  That doesn't mean we have been sitting on our hands either though.  Here is what we had accomplished the last few weeks...

Amy and I got the interior all taped off for the paint inside the hatches.  You will notice all of the bulkheads, side deck supports and cross deck supports are all in and permanently installed.


Ready for paint.


Here we are in progress painting the inside of the hatches.  The Tequila Beach color looks really nice.  Kirby Paint makes some VERY nice paint!





The paint took several days to cure out before it was not tacky.  We had some cooler days with a little higher humidity than usual, so that likely explains it.

Once the painting was done, it was time to get after oiling the inner wood that will remain wood once the decks go on.  This is Kirby's Salty Dog Deck Oil.


Here is what it looks like with the frames all oiled up.  I will get a second coat on once all of the remaining hatch pieces go in.
Gary and Chad came over last week and we installed the deck supports at the Front & Transom areas, along with some other miscellaneous items. I was a little preoccupied since I had confirmed my spot on a 16-day River Trip down Grand Canyon for this July.  The dory will not be making that trip.

We have had such a nice, mild winter here in Las Vegas, so this past Sunday Amy, our friend Rachel and me all went up to Red Rock for a hike up to Stoner's Chairs.  The pictures below include a shot into Red Rock NCA, and a view back towards the Las Vegas Valley.


Thursday, January 30, 2014

Glassing, Sanding & Thwarts, Oh My!

So remember when I said I was going to post more Blog updates?  Ok good, I was hoping that one went pretty much unnoticed.  So the last time we were all together here we had just finished cutting down the sides and had lofty dreams of unicorns, epoxy and fiberglass.  Well I was getting low on Epoxy, and had about 3/4 of a gallon of WEST left.  Knowing this was not going to be enough to do much of anything, we ordered more.  And some other stuff.  Lots of heavy other stuff.

We began by getting this rear section of the bottom glassed up with the last of the epoxy that was on-hand.


Unfortunately, there was not enough left to do this section or the middle section.  Full disclosure, I also needed more fiberglass to do the center section, so it was not just a function of being out of resin.

Another shot.  Glass is cut, fitted and ready for epoxy.

While I was waiting for more stuff to show up that I had ordered, the paint for the inside of the hatches and the exposed deck areas showed up.  George Kirby Jr Paint Company is not my discovery.  Brad Dimock is using this stuff on his Dories, and he had gone to the trouble to take a jar of sand from Below Lava (Tequila Beach) and have it color matched into a boat paint.  So yeah, he did all of the hard work, and the guys at Kirby Paint get some more money out of the deal.  Win-win in my book.  I also ordered some 'Salty Dog Deck Oil' for the inside pieces that do not get fiberglass.

So the day finally came.  I had a 5 day break on boat building, but my Epoxy and fiberglass showed up from Raka.  Note the roll of fiberglass weighed 136 pounds!


Now that I had supplies I was able to finish glassing the interior.  This is 18oz glass.  I'm still not sure what weight the other glass was that I used on the bottom, but it is probably 30oz+, and there are 2 layers on the inside of the bottom.

Starting to glass up the interior components we had cut a few weeks back.  These are the sides of the boatmens footwell and our inlay piece for the transom. 

 Getting everything fitted in the stem.

 Here it is Post-epoxy

Getting ready to cut out for the bulkhead glassing project.

 Getting the transom area cut and ready for epoxy.  Figured I could get some added strength for the bow-eye by overlapping the layers.  Makes sense right?  The epoxy resin in the background didn't last long.

Glass was cut for all of the bulkheads at the same time, so I could just get them sticky.  This all took place in nightly 4 hour shifts over the course of 4 days.

Closeup of the transom area.
 

First 3 bulkheads wetted out.


Transom is kicking

 Here is the remaining cloth cut for the bulkheads.  I then started cutting out all of the pieces to finish the sides.  Some important lessons have been learned thus far:

1.  Glass the plywood for the sides before you assemble the boat.
2.  Blue tape is a bad idea. 




 Next round of bulkheads.

Loose fitting and pre-cutting all of the side pieces.

Overall shot of Matkat Werks

Before of the front 4 areas about to be pummeled by epoxy.

Done.

Couple more trimmed and ready for resin.
A couple more bulkheads done.

 Last bulkhead glassed up.


A few more sections of the inside all ready to kick.


A few more.  Getting closer, but will there be enough epoxy???



All ready to sand.  Gasp.  Lots of sanding to do!

All of these were tackled at once, and there was just barely enough resin to do the job.

But the job got done.  Woo hoo!



 Here is a recap:
-The bottom has 2 layers of thick glass, epoxy and a flow coat.
-The sides are all glassed up with 18oz fabric
-The 'wet side' of all of the bulkheads (thwarts) are all glassed with 18oz of fabric.
-All of the extra fiberglass was sanded off inside the boats, along the top and on all of the bulkhead pieces.
-The inside of the boat and surface of the bulkheads were sanded to 220 grit.

So now that all of that work was done, the bulkheads and deck supports were all clamped back in to see how it all fits.  




I then went about the task of screwing, bolting and putting 5200 on everything.   Going to spend some time getting the rear hatch opening sorted out so that it will take a cooler, so then the deck supports can go in and start on the hatches, decks, lids etc.






So I learned a lot in the last few weeks.  One of the most important lessons, was to order materials before you need them.  Of course, this assumes there is an unlimited supply of money.  I planted some quarters, poured on some Miracle Grow, but dammit, still no money tree.  So I sold the brewing equipment.  And I am glad I did.  I now have 3 more gallons of epoxy, the bottom layup materials and all of the latches for the hatches.  Going to pick up some more 5200 tomorrow (fast kick again), then there is a lot to be done and lots of materials on-hand to get it done!